Exothermic Weld Accessories Required for Exothermic Weld Process: 

1) Graphite Mould for having Exothermic Weld                                                                                                   

When making a copper wire connection of Ground rod or other metal connection, place the Exothermic welding powder into the graphite mould. Just ignite to start the Welding process. The result will be clean and smooth connection surface. It is also applicable for other metal such as: Iron, Galvanized Steel, Railway track, Cast Iron, Bronze, and Brass. It can be used in various applications to have the certainly good connections in work. Such as Lightning and Surge Protection, Grounding in Electrical Work, Railway Construction, Cathodic Protection.

The connection mould is designed to last for an average of 60 to 100 connections. This will vary according to the care given the mould during use.Graphite mould is made of high quality graphite suitable for high quality Weldinging work and can be used for several times.

2) Mould Handle Clamp (Universal)

For most connections involving lugs, cable or rectangular bus, exothermic mould handle clamps are used.
These will fit 90% of all standard exothermic molds. Normally we recommend One Handle for every two moulds
These are manufactured by the professionals using high quality raw material. These Mold Handle Clamp conform their adherence with the industry standards.

3) Steel Metal Disk 

Steel discs are very important. The disc acts timing device to allow the Exothermic Weld Powder to heat to proper temperature. Steel Disk is designed to contain the exothermic reaction to the upper crucible of a mold until the reaction is complete and ready to Welding. One Metal is must for every shot 


4) Exothermic Weld Powder 

Exothermic Weld Powder is the most reliable and consistently-performing Welding metal available with us. 
Quality validation steps are taken for every lot we produce. Upon final acceptance, our Welding metal is 
specially packaged  in moisture-resistant plastic cartridges with special closure caps. Then the cartridges
and required metal discs are packaged in moisture-resistant boxes.

Our standard packing for Exothermic Weld Powder is the following - 
Firstly Exothermic Weld Powder is in the tube and starting powder / Ignite Powder is in tube at the bottom of 
Exothermic Weld Powder as shown in diagram 

Moisture Free Packing in Foil

All sizes of Welding metal are available. 
Standards Size Packing available are – 50 Grams, 100 Grams, 125 Grams, 150 Grams, 200 Grams, 250 Grams, 1 Kilogram


5) Ignite Powder (Starting Powder) 

Ignite Powder is  also known as Starting Powder and is required and is must. Sprinkle little Starting Powder on the Mould followed by the Exothermic Weld Powder and again sprinkle it little on the Top Side of Mould. Than Ignite starting powder with a spark gun.

This results in exothermic reaction and the Weld Powder melts to molten copper alloy. The molten copper alloy melts the retaining disc and flows into the Welding cavity where it partially melts the conductors. 

Ignite Powder of 2-4 grams is sufficient


6) Gloves

Gloves is required for safety purpose as the Exothermic Weld Powder melts at more than 1400 degree Celcius.
We recommend a Pair of Gloves for Every 100 Joints


7) Flint Gun

It is designed with the advantages of safety and convenience. It is used to ignite Starting Powder in order to result in exothermic reaction. 
We recommend one Flint Gun for every 100 Shots 

8) Brush (Soft and Hard)

Two Brush Required:

A) Soft Brush – Its used to Clean Mould Welding Cavity because its shape is very sensitive and there should not be any damage while using Brush, so we recommend to use Soft 

B) Hard Brush – Its used to clean other section of Mould
We recommend a Pair of Brush for 25 Connection 

 
9) Slag Removal Tool

It is used to remove the metal Scrap from Mould after the Welding Process is done.
We recommend One Slag Tool for Every 100 Joints
 

10) File Card 

It is used to clean the objects to be Weld.
We recommend One Slag Tool for Every 50 Joints

11) Sealing Compound

Sealing Compound is used to fill the gap on the mould where the conductor is passing
We recommend 1 Kg Sealing Compound for Every 50 Joints


12) Flame Torch

Graphite absorbs moisture from weather. So there is a need for propane torch to dry out the inside of the mould 
thoroughly on both sides, therefore heating the mold to approximately 250 degrees Fahrenheit
We recommend using one Flame torch for Every 100 Joint and than use the refiling.

13) Sun Glass

Sun Glass is Using For Eye Safety  
We Recommend Using Sun Glass For Every 100 Joint.